CPA24

Power amplifier 240W 100V

Highlights

  • 24 Volts emergency power operation
  • Terminal block output connections ( 4Ω, 25V, 70V & 100V)
  • XLR input & linkthrough connections with gain control
  • Class A/B amplifier technology
  • Advanced protection circuit
  • Ground lift switch
  • High-pass filter switch

Applications

  • Public facilities
  • Retail
  • Corporate spaces
  • Bars, restaurants
3 years

The CPA24 is a professional single channel 100V power amplifier with a power of 240 Watt, especially designed for most common 100V PA systems, and perfect to be used in combination with the CPR12 pre-amplifier. It is designed as a no-nonsense amplifier with only the necessary controls and connections. This creates great simplicity in use and installation. There are several power output taps available for use in 100V, 70V and even 4 Ohm Low impedance installations and they are fitted with an advanced multipurpose protection circuit. The protection circuit detects DC malfunction, short circuit, overheating, overload and limits the signal when necessary. Another present feature is the 24 V DC connection for powering the amplifier with emergency power when the main power is shut down. At the back of the amplifier, there are trim potentiometers to set the input level, a high pass filter switch and a ground lift switch provided. The input connection is made with balanced XLR connectors, and there’s a signal output for linking with other amplifiers. The steel 19" housing has a height of 2 HE.

System specifications
RMS Power 240 W
Frequency Response (± 3 dB) 70 Hz - 18 kHz
Signal / Noise > 90 dB
THD+N (@ 1 kHz) < 1%
Technology Class A/B
Power Supply Conventional (Transformer)
Source 230 ~ 240 V AC / 50 ~ 60 Hz (110~115 V AC / 50~60 Hz after connection change)
Inputs Sensitivity (1W/1m) -12 dB ~ 0 dB
Impedance 10 kΩ balanced
Connector XLR female with Male Linkthrough
Outputs Voltage / Impedance 100 V / 42 Ω
70 V / 21 Ω
31 V / 4 Ω
Connector 4-pin Euro Terminal block (Pitch - 7.62 mm with locking)
Protection DC Short circuit
Over heating
Over load
Signal limiting
Cooling Dual speed controlled FAN
Operating temperature 0° ~ 40° @ 95% Humidity
Product Features
Dimensions 18.98 x 3.46 x 12.99 " (W x H x D)
Weight 28.66 lb
Mounting 19”
Unit height 2 HE
Construction Steel
Colours Black
Accessories Included 4-pin Euro Terminal Block outputs connector
2-pin Euro Terminal Block 24V Power connector
Optional CPE100 Rack mount handles

Product

Answer

As the power consumption of an amplifier, strongly depends on how hard the amplifier is driven, measurements are provided for various loads: idle, 1/8 of average full power, 1/3 of average full power, and full power.

Idle 
Current draw at idle or with very low signal level

1/8 Power: Pink Noise
Amplifiers are tested using pink noise signals to simulate real-world speech and music signals.  It approximates operating with music or voice with light clipping and represents the amplifier's typical "clean" maximum level, without audible clipping. This 1/8 power signal provides a very good approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven as loud as possible without clipping the amplifier.

1/3 Power: Pink Noise
1/3 Power Pink Noise is similar to 1/8 Power Pink Noise, except that it is a significantly more powerful input signal. It approximates operating with music or voice with very heavy clipping and a very compressed dynamic range. This 1/3 power signal provides an approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven loud enough to clip the amplifier heavily, and produce severe, audible distortion.

Full Power
Current draw at full power is measured with a sine wave at its maximum possible level. However, it does not represent any real-world operating condition and represents the absolute extremes that an amplifier could ever experience.
 

Information sheet English

Create a document that summarizes all the details of this product. The product information sheet can contain: product descriptions, technical drawings, technical specifications, architect’s and engineer’s specifications, shipping and ordering details, product applications, ...

Information sheets other languages

Code Quantity Length Width Height Cubage Weight
PRODUCT 1 0,32 m 0,48 m 0,09 m 0,01386 m³ 13,30 kg
PCS 1 0,56 m 0,42 m 0,19 m 0,04287 m³ 14,60 kg
INNER 1 - - - - -
MASTER 3 - - - - -
PALLET 23 - - - - 325,45 kg
CPA24 - Power amplifier 240W 100V

CPA24

EAN: 5414795008656
Top