Dual-channel power amplifier 2 x 240W 100V
- Terminal block output connections
- XLR input & linkthrough connections with gain control & HPF switch
- Lightweight class-D amplifier
- Advanced protection circuit
- High-pass filter switch
- Public facilities
- Corporate spaces
- Clubs, bars, restaurants
The CAP series are professional 100V multi-channel power amplifiers. The CAP224 offers two channels and has an output power of 240 Watt. This way, a flexible solution is created for multi-zone audio distribution systems with two independent zones. They are designed as no-nonsense amplifiers with only the necessary controls and connections which creates great simplicity in use and installation. A high efficiency and reliability of the device is achieved by using switching power supplies in combination with Class-D amplifier technology. A temperature controlled fan constantly keeps all parts within the right operation range while avoiding excessive buzz. A built-in multipurpose protection circuit protects against DC malfunction, short circuit, overheating, overload and limits the signal when necessary. The input connections are performed using balanced XLR connectors and link output connectors are provided for link through to other amplifiers. Besides, a high-pass filter switch (400 Hz) and a gain adjustment potentiometer are provided for each channel. The output connections are performed using reliable terminal block connectors and this all is housed into a solid constructed, double rack space (2 HE) 19” rack mounting housing.
|RMS Power||2 x 240 W|
|Frequency||Response (± 3 dB)||50 Hz - 22 kHz|
|Signal / Noise||> 100 dB|
|THD+N (@ 1 kHz)||< 0.3% (1/2 Rated Power)|
|Crosstalk (@ 1 kHz)||< 80 dB|
|Source||230 ~ 240 V AC / 50 Hz|
|Inputs||Sensitivity (1W/1m)||-0.5 dB ~ 10.5 dB|
|Impedance||10 kΩ balanced|
|Connector||XLR female with Male Linkthrough|
|Outputs||Voltage / Impedance||100 V / 42 Ω|
|Connector||4-pin Euro Terminal Block (Pitch - 5.08 mm)|
|Common mode rejection ratio||70 dB|
|Protection||DC Short circuit|
|Cooling||Temperature controlled FAN|
|Operating temperature||0° ~ 40° @ 95% Humidity|
|Dimensions||18.98 x 3.46 x 16.54 " (W x H x D)|
|Unit height||2 HE|
|Accessories||Included||2 x 4-pin Euro Terminal Block outputs connector|
|Optional||CPE100 Rack mount handles|
|Product||Unit of measure||Quantity|
|AU960103009 - CAP224 DEVICE||PCS||1||ExpandCollapse|
|AU710802041 - CON CBL 4P TERM. BLOCK 5.08MM GREEN||PCS||2|
As the power consumption of an amplifier, strongly depends on how hard the amplifier is driven, measurements are provided for various loads: idle, 1/8 of average full power, 1/3 of average full power, and full power.
Current draw at idle or with very low signal level
1/8 Power: Pink Noise
Amplifiers are tested using pink noise signals to simulate real-world speech and music signals. It approximates operating with music or voice with light clipping and represents the amplifier's typical "clean" maximum level, without audible clipping. This 1/8 power signal provides a very good approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven as loud as possible without clipping the amplifier.
1/3 Power: Pink Noise
1/3 Power Pink Noise is similar to 1/8 Power Pink Noise, except that it is a significantly more powerful input signal. It approximates operating with music or voice with very heavy clipping and a very compressed dynamic range. This 1/3 power signal provides an approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven loud enough to clip the amplifier heavily, and produce severe, audible distortion.
Current draw at full power is measured with a sine wave at its maximum possible level. However, it does not represent any real-world operating condition and represents the absolute extremes that an amplifier could ever experience.
Information sheet English
Create a document that summarizes all the details of this product. The product information sheet can contain: product descriptions, technical drawings, technical specifications, architect’s and engineer’s specifications, shipping and ordering details, product applications, ...
|PRODUCT||1||0,48 m||0,42 m||0,09 m||0,01814 m³||7,20 kg|
|PCS||1||0,55 m||0,51 m||0,15 m||0,04321 m³||10,68 kg|